Reinforced Shock Absorber - Adjustable (8 Positions) - Front Fitment - McPherson - Nitrogas - Mitsubishi & Fiat - Sandkat4x4
Manufacture Sandkat4x4
260,00 € // Prix HT : 216,67 €
Limited stockReference > SRA030008
Adjustable Shock Absorber (8 Positions) - Rear Fitment
Approximately 6cm of lift
Reinforced for usage on all terrains
All of our boxes of shocks contain the necessary bushes, nuts, and bolts.
For Mitsubishi & Fiat
Approximately 6cm of lift
Reinforced for usage on all terrains
All of our boxes of shocks contain the necessary bushes, nuts, and bolts.
For Mitsubishi & Fiat
| Brand | Model |
|---|---|
| MITSUBISHI | PAJERO Sport 2015+ |
| MITSUBISHI | Pajero Sport 2008+ |
| MITSUBISHI | L200 MQ 2015+ |
| MITSUBISHI | L200 MN 2012>2015 |
| MITSUBISHI | L200 ML 2006>2012 |
| FIAT | Fullback 2016+ |
Sandkat4x4 MANUFACTURING
Adjustable Nitrogas shocks (8 Positions) designed for optimum off-road performance
FEATURES - Large fluid capacity 35 mm bore with double lip urethane seals, sintered iron piston, 16 mm hard chromed piston rod, double welded eye mounts.
TRAVEL - Approximately 50 mm longer travel to suit the extra lift on the springs.
BUSH MOUNTS - Quality rubber bushes for greater fatigue life and wear resistance.
GAS CHARGED - Nitrogen gas cushion to prevent fluid foaming and improve control and handling.
HYDRAULIC FLUID - Top performance oil resists the most extreme temperatures from -40°C to + 120°C.
FINISH - Tough durable electrostatic paint finish to protect against rust and corrosion.
:
Mounting: Front
Fixation: Pin/Eye
Compression 311mm
Extension 431mm
Top PIN10
Bottom CR5-14x50
Note:
Shock priming
The shock should be “primed” before installation: Hold the shock vertical on the ground (normal installation position) and then push down on the shock to fully compress it and then fully extended it several times.
The first movement or two may feel like the shock isn’t working due to its low nitrogen gas pressure that sometimes seeps into the hydraulic area during extended horizontal storage. If this procedure is not performed prior to installation, noisy operation and loss of performance can occur for a short time.
Never try to open or heat.
Always tighten the shocks when the vehicle is laying on the ground.
Adjustable Nitrogas shocks (8 Positions) designed for optimum off-road performance
FEATURES - Large fluid capacity 35 mm bore with double lip urethane seals, sintered iron piston, 16 mm hard chromed piston rod, double welded eye mounts.
TRAVEL - Approximately 50 mm longer travel to suit the extra lift on the springs.
BUSH MOUNTS - Quality rubber bushes for greater fatigue life and wear resistance.
GAS CHARGED - Nitrogen gas cushion to prevent fluid foaming and improve control and handling.
HYDRAULIC FLUID - Top performance oil resists the most extreme temperatures from -40°C to + 120°C.
FINISH - Tough durable electrostatic paint finish to protect against rust and corrosion.
:
Mounting: Front
Fixation: Pin/Eye
Compression 311mm
Extension 431mm
Top PIN10
Bottom CR5-14x50
Note:
Shock priming
The shock should be “primed” before installation: Hold the shock vertical on the ground (normal installation position) and then push down on the shock to fully compress it and then fully extended it several times.
The first movement or two may feel like the shock isn’t working due to its low nitrogen gas pressure that sometimes seeps into the hydraulic area during extended horizontal storage. If this procedure is not performed prior to installation, noisy operation and loss of performance can occur for a short time.
Never try to open or heat.
Always tighten the shocks when the vehicle is laying on the ground.
You are a Professional ?
Contact us now
Prices shown are for consumers and include VAT. Companies, Professionals, please contact us to obtain your specific conditions.
Devenir Professionnel
